Viaterra Holeshot Summer Mesh Black Hybrid Gloves Viaterra Holeshot Summer Mesh Black Hybrid Gloves Riderz Planet Viaterra Holeshot Summer Mesh Black Hybrid Gloves Safety is paramount even during your daily commute.  Keeping this in mind we have designed the Holeshot to offer comfort along with protection even during your day-to-day commute. Holeshot offers high airflow through the 3D air mesh panel on the back of your hand and between the fingers yet provides maximum protection by incorporating perforated goatskin leather on the palm. In addition, we have integrated KNOX SPS sliders as well on the palm to prevent Scaphoid injuries caused by the grab effect when the palm comes in contact with the road in case of a fall. Leather The Holeshot Uses Goatskin leather that is durable , light and natural  water resistant . It is the most comfortable leather to use in gloves due to its suppleness . We kept the thickness of the leather to the highest level possible (1.2 to 1.5mm) to ensure enhanced abrasion resistance . Knox sps scaphoid injuries are the most common hand injury in motorcycle accident . These are caused by the  grab effect when the palm of the hand makes contact with the ground . We chose the low profile Knox sps 303 for the holeshot is because it is small enough to not interfere during day to day  use but  at the  same time offer  much needed protection   to the  scaphoid  area . Because it is important , we worked with knox to ensure we get the placement of the sps absolutely correct final production samples were physically  verified at the knox headquarters  in london for approval before the production run . Tpu Protectors Tpu protector are placed over the knuckles on the holeshot to ensure they are well protected by absorbing  the impact foam layer is placed under the tpu protector for comfort Silicone Grip The Holeshot has an engineered  super grip silicone panel  attached at the purlicue  (the area between forefinger and thumb ) which much offer much superior grip on the bars . Most other gloves have heat transfer branding details in the area that doesn’t  significantly improve grip . You can run your finger on the grip panel to check this . Having a gripper palm allows you to hold the bars lightly while ensuring you are able to operate the throttle smoothly . Touch Screen Friendly . Things to Remember:  Putting on and taking off may be slightly difficult, because the wrist area is narrowed down for safety reasons. This is done to prevent the gloves from coming off your hands during a crash and to offer a snug fit. If you have never used gloves with a pinky bridge you may find it odd or uncomfortable. Give it a few days of riding and you will get used to it. Remember, any protective gear is relatively uncomfortable to wear compared to riding without any protection. You may find the Knox SPS on the palm to be uncomfortable in the first try. But just like any protective gear, over a period of time you will get used to it so you do not even notice it. These devices are incorporated in the gloves is to ensure you are well protected when you most need it. In our research, we found that the palm size and the finger length are not in the same proportion for everyone (that makes each of us unique in the truest sense!). In such cases, primary area of fitment should always be the palm area, even if you are to be left with some extra room near your fingertips. We have used high density TPU to maximise protection and longevity. While we have added an additional foam layer underneath the TPU, they may feel a bit too hard at the beginning. Thinner and more flexible knuckle protectors are not very effective during a crash and do not last long either. Care Instructions: Our gloves use full-grain goat leather that is naturally water-resistant. This means that the gloves do not get ruined if they get wet in rains. However, when leather gets wet, the oils get stripped from the leather – this  will stiffen the leather and eventually cause it to crack. Think of it as your skin after taking a bath – you need to moisturize to replace the natural oils in your skin removed by the water. So, what matters for your gloves is what you do after it gets wet.  Here is a step by step process to keep your glove well cared for and last longer. If your gloves get wet, dry the gloves by pressing softly with an absorbent towel. If there are stains, clean the gloves by hand with a pH neutral leather cleaner using a damp cloth or a soft-bristled brush. DO NOT USE HOT WATER DO NOT allow your gloves to come in contact with solvents (do not use fabric softener!), fuel, or cleaning agents. DO NOT use any kind of CHEMICAL or ALCOHOL-BASED product. Do not use a washing machine or high-pressure devices to clean the gloves, as high temperatures and pressure will damage the leather. Do not place your gloves near, or let your gloves get into contact with a direct heat source – this will harden the leather and lead to damage. Also dry the gloves indoors away from direct sunlight where there is good ventilation. Just before the gloves are completely dry, put the gloves on and shape them to your hand while still damp. Remove the gloves gently, trying to retain this shape in the gloves and allow it to continue drying.  After the gloves are completely dry, apply a good quality leather conditioner. This is very important. Properly treated and conditioned (oiled) leather will breathe and the internal microfibers will move freely in the leather. Use a good quality leather conditioner that will allow the leather to breathe. Apply conditioner generously and rub it into the leather. Allow the conditioner to soak into the gloves and reapply (you can do this in the sun). Wipe off any excess conditioner and make sure the gloves are not slick on the motorcycle controls. Make sure that your gloves are completely dry before you store them. When gloves are stored wet or in a non-ventilated area, this may cause deformations and ruin your gloves, not to mention this allows mildew to grow on the leather causing discoloration and damage.

Viaterra Holeshot Summer Mesh Black Hybrid Gloves

Code/SKU/Compound 002198
Add Your Review
Viaterra Holeshot Summer Mesh Black Hybrid Gloves Viaterra Holeshot Summer Mesh Black Hybrid Gloves Viaterra Holeshot Summer Mesh Black Hybrid Gloves Viaterra Holeshot Summer Mesh Black Hybrid Gloves
Viaterra Holeshot Summer Mesh Black Hybrid Gloves
Viaterra Holeshot Summer Mesh Black Hybrid Gloves Viaterra Holeshot Summer Mesh Black Hybrid Gloves Viaterra Holeshot Summer Mesh Black Hybrid Gloves Viaterra Holeshot Summer Mesh Black Hybrid Gloves
Rs. 2,899.00
In Stock
Add to Wishlist Add to Compare
Category: GLOVES, NEW ARRIVALS, VIATERRA

Viaterra Holeshot Summer Mesh Black Hybrid Gloves

Safety is paramount even during your daily commute. 

Keeping this in mind we have designed the Holeshot to offer comfort along with protection even during your day-to-day commute. Holeshot offers high airflow through the 3D air mesh panel on the back of your hand and between the fingers yet provides maximum protection by incorporating perforated goatskin leather on the palm. In addition, we have integrated KNOX SPS sliders as well on the palm to prevent Scaphoid injuries caused by the grab effect when the palm comes in contact with the road in case of a fall.

Leather

The Holeshot Uses Goatskin leather that is durable , light and natural  water resistant . It is the most comfortable leather to use in gloves due to its suppleness . We kept the thickness of the leather to the highest level possible (1.2 to 1.5mm) to ensure enhanced abrasion resistance .

Knox sps

scaphoid injuries are the most common hand injury in motorcycle accident . These are caused by the  grab effect when the palm of the hand makes contact with the ground . We chose the low profile Knox sps 303 for the holeshot is because it is small enough to not interfere during day to day  use but  at the  same time offer  much needed protection   to the  scaphoid  area . Because it is important , we worked with knox to ensure we get the placement of the sps absolutely correct final production samples were physically  verified at the knox headquarters  in london for approval before the production run .

Tpu Protectors

Tpu protector are placed over the knuckles on the holeshot to ensure they are well protected by absorbing  the impact foam layer is placed under the tpu protector for comfort

Silicone Grip

The Holeshot has an engineered  super grip silicone panel  attached at the purlicue  (the area between forefinger and thumb ) which much offer much superior grip on the bars . Most other gloves have heat transfer branding details in the area that doesn’t  significantly improve grip . You can run your finger on the grip panel to check this . Having a gripper palm allows you to hold the bars lightly while ensuring you are able to operate the throttle smoothly .

Touch Screen Friendly .

Things to Remember: 

  • Putting on and taking off may be slightly difficult, because the wrist area is narrowed down for safety reasons. This is done to prevent the gloves from coming off your hands during a crash and to offer a snug fit.
  • If you have never used gloves with a pinky bridge you may find it odd or uncomfortable. Give it a few days of riding and you will get used to it. Remember, any protective gear is relatively uncomfortable to wear compared to riding without any protection.
  • You may find the Knox SPS on the palm to be uncomfortable in the first try. But just like any protective gear, over a period of time you will get used to it so you do not even notice it. These devices are incorporated in the gloves is to ensure you are well protected when you most need it.
  • In our research, we found that the palm size and the finger length are not in the same proportion for everyone (that makes each of us unique in the truest sense!). In such cases, primary area of fitment should always be the palm area, even if you are to be left with some extra room near your fingertips.
  • We have used high density TPU to maximise protection and longevity. While we have added an additional foam layer underneath the TPU, they may feel a bit too hard at the beginning. Thinner and more flexible knuckle protectors are not very effective during a crash and do not last long either.

Care Instructions:

Our gloves use full-grain goat leather that is naturally water-resistant. This means that the gloves do not get ruined if they get wet in rains. However, when leather gets wet, the oils get stripped from the leather – this  will stiffen the leather and eventually cause it to crack. Think of it as your skin after taking a bath – you need to moisturize to replace the natural oils in your skin removed by the water. So, what matters for your gloves is what you do after it gets wet. 

Here is a step by step process to keep your glove well cared for and last longer.

  • If your gloves get wet, dry the gloves by pressing softly with an absorbent towel.
  • If there are stains, clean the gloves by hand with a pH neutral leather cleaner using a damp cloth or a soft-bristled brush. DO NOT USE HOT WATER
  • DO NOT allow your gloves to come in contact with solvents (do not use fabric softener!), fuel, or cleaning agents. DO NOT use any kind of CHEMICAL or ALCOHOL-BASED product.
  • Do not use a washing machine or high-pressure devices to clean the gloves, as high temperatures and pressure will damage the leather.
  • Do not place your gloves near, or let your gloves get into contact with a direct heat source – this will harden the leather and lead to damage. Also dry the gloves indoors away from direct sunlight where there is good ventilation.
  • Just before the gloves are completely dry, put the gloves on and shape them to your hand while still damp. Remove the gloves gently, trying to retain this shape in the gloves and allow it to continue drying. 
  • After the gloves are completely dry, apply a good quality leather conditioner. This is very important. Properly treated and conditioned (oiled) leather will breathe and the internal microfibers will move freely in the leather. Use a good quality leather conditioner that will allow the leather to breathe. Apply conditioner generously and rub it into the leather. Allow the conditioner to soak into the gloves and reapply (you can do this in the sun). Wipe off any excess conditioner and make sure the gloves are not slick on the motorcycle controls.
  • Make sure that your gloves are completely dry before you store them. When gloves are stored wet or in a non-ventilated area, this may cause deformations and ruin your gloves, not to mention this allows mildew to grow on the leather causing discoloration and damage.

    Viaterra Holeshot Summer Mesh Black Hybrid Gloves

    Safety is paramount even during your daily commute. 

    Keeping this in mind we have designed the Holeshot to offer comfort along with protection even during your day-to-day commute. Holeshot offers high airflow through the 3D air mesh panel on the back of your hand and between the fingers yet provides maximum protection by incorporating perforated goatskin leather on the palm. In addition, we have integrated KNOX SPS sliders as well on the palm to prevent Scaphoid injuries caused by the grab effect when the palm comes in contact with the road in case of a fall.

    Leather

    The Holeshot Uses Goatskin leather that is durable , light and natural  water resistant . It is the most comfortable leather to use in gloves due to its suppleness . We kept the thickness of the leather to the highest level possible (1.2 to 1.5mm) to ensure enhanced abrasion resistance .

    Knox sps

    scaphoid injuries are the most common hand injury in motorcycle accident . These are caused by the  grab effect when the palm of the hand makes contact with the ground . We chose the low profile Knox sps 303 for the holeshot is because it is small enough to not interfere during day to day  use but  at the  same time offer  much needed protection   to the  scaphoid  area . Because it is important , we worked with knox to ensure we get the placement of the sps absolutely correct final production samples were physically  verified at the knox headquarters  in london for approval before the production run .

    Tpu Protectors

    Tpu protector are placed over the knuckles on the holeshot to ensure they are well protected by absorbing  the impact foam layer is placed under the tpu protector for comfort

    Silicone Grip

    The Holeshot has an engineered  super grip silicone panel  attached at the purlicue  (the area between forefinger and thumb ) which much offer much superior grip on the bars . Most other gloves have heat transfer branding details in the area that doesn’t  significantly improve grip . You can run your finger on the grip panel to check this . Having a gripper palm allows you to hold the bars lightly while ensuring you are able to operate the throttle smoothly .

    Touch Screen Friendly .

    Things to Remember: 

    • Putting on and taking off may be slightly difficult, because the wrist area is narrowed down for safety reasons. This is done to prevent the gloves from coming off your hands during a crash and to offer a snug fit.
    • If you have never used gloves with a pinky bridge you may find it odd or uncomfortable. Give it a few days of riding and you will get used to it. Remember, any protective gear is relatively uncomfortable to wear compared to riding without any protection.
    • You may find the Knox SPS on the palm to be uncomfortable in the first try. But just like any protective gear, over a period of time you will get used to it so you do not even notice it. These devices are incorporated in the gloves is to ensure you are well protected when you most need it.
    • In our research, we found that the palm size and the finger length are not in the same proportion for everyone (that makes each of us unique in the truest sense!). In such cases, primary area of fitment should always be the palm area, even if you are to be left with some extra room near your fingertips.
    • We have used high density TPU to maximise protection and longevity. While we have added an additional foam layer underneath the TPU, they may feel a bit too hard at the beginning. Thinner and more flexible knuckle protectors are not very effective during a crash and do not last long either.

    Care Instructions:

    Our gloves use full-grain goat leather that is naturally water-resistant. This means that the gloves do not get ruined if they get wet in rains. However, when leather gets wet, the oils get stripped from the leather – this  will stiffen the leather and eventually cause it to crack. Think of it as your skin after taking a bath – you need to moisturize to replace the natural oils in your skin removed by the water. So, what matters for your gloves is what you do after it gets wet. 

    Here is a step by step process to keep your glove well cared for and last longer.

    • If your gloves get wet, dry the gloves by pressing softly with an absorbent towel.
    • If there are stains, clean the gloves by hand with a pH neutral leather cleaner using a damp cloth or a soft-bristled brush. DO NOT USE HOT WATER
    • DO NOT allow your gloves to come in contact with solvents (do not use fabric softener!), fuel, or cleaning agents. DO NOT use any kind of CHEMICAL or ALCOHOL-BASED product.
    • Do not use a washing machine or high-pressure devices to clean the gloves, as high temperatures and pressure will damage the leather.
    • Do not place your gloves near, or let your gloves get into contact with a direct heat source – this will harden the leather and lead to damage. Also dry the gloves indoors away from direct sunlight where there is good ventilation.
    • Just before the gloves are completely dry, put the gloves on and shape them to your hand while still damp. Remove the gloves gently, trying to retain this shape in the gloves and allow it to continue drying. 
    • After the gloves are completely dry, apply a good quality leather conditioner. This is very important. Properly treated and conditioned (oiled) leather will breathe and the internal microfibers will move freely in the leather. Use a good quality leather conditioner that will allow the leather to breathe. Apply conditioner generously and rub it into the leather. Allow the conditioner to soak into the gloves and reapply (you can do this in the sun). Wipe off any excess conditioner and make sure the gloves are not slick on the motorcycle controls.
    • Make sure that your gloves are completely dry before you store them. When gloves are stored wet or in a non-ventilated area, this may cause deformations and ruin your gloves, not to mention this allows mildew to grow on the leather causing discoloration and damage.

      Excellent, Now You can get it better...

      Get 10% discount when you share on Social Platforms

      Thank You, Your discount code: